Houston240sx.com Forums  
Enjuku Racing

Go Back   Houston240sx.com Forums > Houston240sx.com > Tech Discussion > General Maintenance

Reply
 
Thread Tools Display Modes
Old 01-06-2015, 08:26 PM   #1
Fearless
Registered User
 
Join Date: Jul 2011
Location: Houston,Tx
Posts: 52
Fearless probable wing man
Lowering Cross-member to drop oil pan.

I'm getting ready to drop my oil pan on my hatch. Never did it before so I'm trying to get a attack plan since time is always limited. Did some research and here are my questions.
If I drop the Cross-member with the power steering lines still attached and how much space will this give me?

Also going to try to loosing the motor mounts and jack up the motor by the trans to try to get some more space. Have to figure out how to break them loose. Does anything need to be unplugged harness wise for this? Doing this by myself so trying to get it all figured out. Thanks ahead of time.

Last edited by Fearless; 01-06-2015 at 10:23 PM.
Fearless is offline   Reply With Quote
Old 01-07-2015, 01:38 AM   #2
reppin tha H
Registered User
 
Join Date: Jun 2012
Location: Houston
Posts: 229
reppin tha H probable wing man
You shouldn't have an issue with the harness or getting the pan off by doing what you've stated. The huge problem you will run into is reinstalling the oil pan and getting the rtv to seal. Two things are going to 99% sure to happen; you're indefinitely going to scrape the rtv off on something when trying to position the pan, leaving a bare spot where you will have a huge leak. And, there is oil on the inside of the block that is going to be running down to the mating surface of the oil pan that will contaminate the rtv and also cause a massive leak.
reppin tha H is offline   Reply With Quote
Old 01-07-2015, 07:57 AM   #3
Tatchump
Chump Racer
 
Tatchump's Avatar
 
Join Date: Apr 2011
Location: LaPorte
Posts: 327
Tatchump probable wing man
Just jacking the motor up as high as it would go gave me room to get the pan off. I stacked scrap pieces of 2x4 on the shock towers, then put a piece of 4x4 across. You can jack it up on the front of the oil pan. Just use a piece of wood to spread the load. Once I jacked it up, I just used ratchet straps from the exhaust and intake to the 4x4 to hold it in place.

And like he^^ said, take your time on the reinstall. It will be a pain.
__________________
www.nismorons.com
Tatchump is offline   Reply With Quote
Old 01-07-2015, 08:57 AM   #4
vIn@dRiFt@"
xXTHE HUDZXx
 
vIn@dRiFt@"'s Avatar
 
Join Date: Jun 2011
Location: n.e. houstone
Posts: 1,584
vIn@dRiFt@" probable wing man
Are you just using silicone or a gasket fir the oil pan?
__________________
dRiFt oR dIe BeTchis"

Don't Cross Me Betch!!!
vIn@dRiFt@" is offline   Reply With Quote
Old 01-07-2015, 09:16 AM   #5
gregman
ファックユー
 
gregman's Avatar
 
Join Date: Nov 2009
Location: south Houston
Posts: 1,636
gregman probable wing man
make sure to check tightening specs and pattern to re installing bolts.
i normally just put the bolts in just enough to catch. then let it sit for about 5 mins then snug the bolts down in the correct sequence and then go back over them doing only 1/4 of a turn with your ratchet.
gregman is offline   Reply With Quote
Old 01-07-2015, 12:08 PM   #6
rofflehouse
Im Sleepy
 
rofflehouse's Avatar
 
Join Date: Aug 2008
Location: Houston
Posts: 4,169
rofflehouse probable wing man
Do not over torque the pan bolts, they will snap!
__________________
cypresstexasproperties.com
rofflehouse is offline   Reply With Quote
Old 01-07-2015, 03:15 PM   #7
SnafuPossum
ButtSecksMod
 
SnafuPossum's Avatar
 
Join Date: Oct 2008
Location: Tomball
Posts: 6,807
SnafuPossum probable wing man
Motor is attached to the crossmember. It would more then likely be easier to find a way to undo the motor mounts then lift the motor up enough. Ideally you would want to pull the motor out though to make it easier in the long run. Not to mention you can clean everything but thats only if time and tools permit
__________________
Quote:
Originally Posted by RedstarDriver View Post
Mike, what percentile did you graduate in from high school?
Quote:
Originally Posted by stuntmanmike View Post
i swcored top 3% of dropouts
SnafuPossum is offline   Reply With Quote
Old 01-07-2015, 05:27 PM   #8
jackasspyro2
I fuck cats
 
jackasspyro2's Avatar
 
Join Date: Jan 1970
Location: Space
Posts: 1
jackasspyro2 Its up in the air
What i always have done is
loosen motor mounts and subframe
raise motor by jacking trans and let subframe hang with gravity
take off pan bolts.
take off oil pickup tube bolts(you can only do this if you not a fat boy)
slide pan off and silicon or add cork gasket(my preference)
reverse order to reinstall


like i said this only works if your skinny. but i have had much better success with this then trying to silicon. Every time i try to silicon while the pan is still on the motor i mess it up. I know others have had better success with it but i was never as fortunate. haha
jackasspyro2 is offline   Reply With Quote
Old 01-07-2015, 06:50 PM   #9
WileCyot
Registered User
 
Join Date: Oct 2013
Location: NW Houston, TX
Posts: 530
WileCyot probable wing man
Pull motor and do it properly.
__________________
I roll fenders. PM me if you're interested. I use a PBM Fender Roller.
WileCyot is offline   Reply With Quote
Reply

Tags
crossmember, oil pan


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Gulli Theme By M@TR1XC0D3